DSpace Community:
http://dspace.cityu.edu.hk:80/handle/2031/710
Sat, 01 Nov 2014 01:57:57 GMT2014-11-01T01:57:57ZPhotonic microwave frequency mixing using an optically injected semiconductor laser
http://dspace.cityu.edu.hk:80/handle/2031/7309
Title: Photonic microwave frequency mixing using an optically injected semiconductor laser
Authors: Fu, Xuelei (傅雪蕾)
Abstract: The nonlinear dynamics of an optically injected semiconductor laser are investigated
for radio-over-fiber (RoF) downlink transmission through photonic microwave frequency
mixing. Subject to optical injection from a master laser, the single-mode slave laser ex-
hibits a variety of nonlinear dynamical behaviors such as stable-locking, period-one (P1)
oscillation, period-two (P2) oscillation, and chaos.
By properly adjusting the injection conditions, the slave laser in the P1 oscillation acts
as a broadly tunable photonic microwave oscillator. When an external current modulation
at an intermediate frequency (IF) is applied to the slave laser, the P1 oscillation is
modulated accordingly. Frequency mixing yields up-converted frequencies at both
the upper sideband (USB) and the lower sideband (LSB). As the photonic microwave
generated through P1 oscillation can go beyond the relaxation resonance frequency due
to nonlinear dynamics, photonic microwave frequency up-conversion beyond the laser
bandwidth is achieved. Experimentally, a 2.5-Gbps-grade semiconductor laser is applied
to generate P1 oscillation at 18 GHz. It is shown that the up-conversion bandwidth is
limited by the direct modulation response of the slave laser with a linear operational range
of more than 20 dB. When binary phase-shift keying (BPSK) data is modulated on the IF
signal, it is up-converted to the USB and LSB for downlink transmission simultaneously.
Data up-conversion from an IF of 2 GHz to a subcarrier frequency as high as 20 GHz
is experimentally demonstrated. After transmission over a 4-km single-mode fiber to a
base station, the data is recovered with a bit-error rate (BER) below 10−9. Only low-cost
lasers are used and there is no requirement on high-speed electronic mixers or external
modulators. Numerical simulations support the feasibility of extending the approach
to the technologically important window at 60 GHz. Furthermore, the chaotic state the optically injected semiconductor laser is examined for power-over-fiber (PoF)
applications. The stimulate Brillouin scattering (SBS) threshold is significantly increased
by driving the laser into chaotic oscillation, which has a bandwidth much broader than the
Brillouin linewidth. By comparing with the free-running state, the chaotic state provides
a 22-fold increase of the maximum output power to 838 mW, after transmission over a
5-km single-mode fiber. Upon optoelectronic conversion using a photovoltaic (PV) cell,
the obtained electrical power of 44 mW is adequate for advanced low-power RoF remote
units.
Notes: CityU Call Number: TK7872.M5 F8 2010; xvii, 98 leaves : ill. 30 cm.; Thesis (M.Phil.)--City University of Hong Kong, 2010.; Includes bibliographical references.Fri, 01 Jan 2010 00:00:00 GMThttp://dspace.cityu.edu.hk:80/handle/2031/73092010-01-01T00:00:00ZImpact of antenna correlation on multi-user MIMO systems
http://dspace.cityu.edu.hk:80/handle/2031/7013
Title: Impact of antenna correlation on multi-user MIMO systems
Authors: Wang, Hao (汪浩)
Abstract: Multiple-input multiple-output (MIMO) techniques provide a promising solution
to enhance the performance of wireless communication systems. Antenna correlation
exists in practical MIMO systems for two reasons. First, there may be no
sufficient space to separate antenna elements due to the limited physical sizes of
the transmitters and/or the receivers. Second, the practical propagation environments
may not provide sufficient scatters. In a conventional single-user MIMO
system, since antenna correlation results in reduced degrees of freedom (DOF)
and may severely degrade the system capacity, it has been generally regarded as
a negative factor. However, the impact of antenna correlation in multi-user environments
is still limited explored. In this thesis, we make a comprehensive study
on theoretical and practical aspects of multi-user MIMO systems with correlated
fading.
In the first contribution, the capacity of correlated MIMO systems with full
channel state information (CSI) at both the transmitters and the receiver over
multiple access channels (MACs) (i.e. uplink multi-user MIMO systems) is analyzed.
In contrast to the common views, we show that antenna correlation is
potentially beneficial in a multi-user environment. The key is that the spatial
diversity related to user locations (i.e., multi-user diversity) can compensate the
loss of DOF due to antenna correlation. More specifically, it is shown numerically
that there is a cross point between the capacity curves for systems with and
without correlation. Below this point, correlation is advantageous and vice versa.
Moreover, such a point occurs at a rate increasing with the number of mobile units
(MUs) (denoted by K in this thesis), which implies that the range where antenna
correlation is beneficial increases with K. We also quantify this advantage analytically
in the limiting case of K → ∞. In the meanwhile, it is shown numerically
and analytically that there is a similar advantage from antenna correlation for
MIMO MACs with rate constraints. (We call this advantage correlation gain in
this thesis.)
In the second contribution, we study the impact of antenna correlation on the
capacity of MIMO MACs with imperfect CSI at the transmitter (CSIT). We first
consider the case of no CSIT.We prove that isotropic inputs (i.e., the covariance of
transmitted signal for each MU is identity matrix) are the most robust and optimal
ones, and therefore achieve the capacity of such systems. Both numerical results
and theoretical analysis show that although antenna correlation is detrimental in all rate or power range, the capacity degradation decreases with K increasing and
vanishes when K → ∞. These results imply that besides multi-user diversity,
CSIT also plays an important role in exploiting correlation gain. We then study
the systems with partial CSIT in form of channel covariance information (CCI).
Our major finding is that, similar to the scenario of perfect CSIT, antenna correlation
is potentially beneficial in a multi-user environment. We also prove that,
when antennas at MUs are fully correlated, systems with CCI at transmitters
can obtain exact the same correlation gain as that in systems with perfect CSIT.
This indicates that CCI may be enough to exploit the potential benefit of antenna
correlation.
In the third contribution, we extend the results from the MAC scenario to
the broadcast channel (BC) scenario (i.e., downlink multi-user MIMO systems).
Numerical results show that, similar to MIMO MACs, antenna correlation can
potentially improve the capacity of MIMO BCs. We point out that, besides multiuser
diversity and power focusing effect, such a gain mainly comes from the fact
that antenna correlation can increase the variance of the channel gain, which has
already been regarded as a advantageous factor in systems with user scheduling.
We also quantify the correlation gain in BCs for the limiting case of K → ∞ when
antennas at the base station (BS) and/or MUs are fully correlated. Theoretical
analysis shows that the asymptotic correlation gain for the case of full correlation
at both the BS and MUs grows linearly and logarithmically with the antenna
number at the BS, and logarithmically with the antenna number at each MU.
In the final contribution, we consider the practical implementation aspects of
correlation gain in coded MIMO multiple-access systems. To decrease the complexity
of MIMO transmission under imperfect CSIT, we propose two types of
low-cost but asymptotically optimal strategies, i.e. the instantaneous maximum
eigenmode beamforming (MEB) and statistical MEB strategy. Interleave-division
multiple-access (IDMA) technique, as a low-cost iterative multi-user detection
(MUD) approach, is adopted to alleviate inter-user interference resulting from
multi-user concurrent transmission. Simulation results demonstrate that our proposed
transceiver (i.e., MEB-based IDMA system) is an effective platform in practice
to obtain the aforementioned correlation gain.
In summary, this thesis presents a comprehensive study on antenna correlation
in multi-user MIMO systems. Both numerical and analytical results show that
antenna correlation is potential advantageous in a multi-user environment. Such
an advantage mainly comes from three aspects. First, the loss of the spatial
DOF due to antenna correlation is compensated by multi-user diversity. Second, antenna correlation enables focusing power. Third, the variance of the channel
gain is enlarged by antenna correlation, which is beneficial in systems with user
scheduling. The finding in this thesis is useful in practice as minimizing the
physical size of MUs and/or the BS is highly desirable, but it may result in antenna
correlation.
Notes: CityU Call Number: TK5103.4836 .W36 2012; xi, 91, iii leaves : ill. 30 cm.; Thesis (Ph.D.)--City University of Hong Kong, 2012.; Includes bibliographical references (leaves [83]-91)Sun, 01 Jan 2012 00:00:00 GMThttp://dspace.cityu.edu.hk:80/handle/2031/70132012-01-01T00:00:00ZAn investigation into the use of coil-resonators in domino forms for wireless power transfer
http://dspace.cityu.edu.hk:80/handle/2031/6960
Title: An investigation into the use of coil-resonators in domino forms for wireless power transfer
Authors: Zhong, Wenxing (鍾文興)
Abstract: This thesis presents a study on the wireless power transfer systems using coil-resonators in domino forms (called domino-resonator systems or domino-systems in this thesis). The study is based on the lumped circuit model of domino-resonator systems and aims to analyze the operating principles and find out the optimum operations of the systems under different operating conditions. Straight and circular domino-resonator systems with one source resonator (transmitter) and one loaded resonator (receiver) are firstly studied. Then domino-resonator systems consisting of one transmitter and two receivers are investigated. Analysis methods based on superposition theorem, vector diagrams and power path are proposed. From theoretical analysis, simulation results and practical measurements, a number of findings are reported on the operation and optimization of the domino-resonator systems.
Straight domino-resonator systems are studied firstly assuming that the resonators in each system are identical and the operating frequency of the system equals to the resonant frequency of the resonators. Analytical expressions for the optimum load resistance and maximum efficiency are derived for a system with more than 2 resonators when the cross-couplings between non-adjacent resonators are negligible. The optimum arrangement of the resonators in a straight domino-resonator system is then studied. It is shown from theoretical analysis and numerical simulations that the optimum arrangement of the resonators is dependent on the load resistance and that if the load resistance is also optimized then equal-spacing is the best arrangement for a system with 3 resonators, but for a system with more than 3 resonators, the optimum arrangement is not equal-spacing which is different from the equal-spacing arrangement used in domino-resonator systems for waveguide applications.
Next the operating frequency is taken into consideration in the study on the straight domino-resonator system. Power flow analysis shows that there exist more than one power paths in a domino-system with more than 2 resonators due to the cross-couplings of non-adjacent resonators. As verified by analysis and practical measurements, the cross-coupling effects of the non-adjacent resonators cause the optimum operating frequencies for both the equally-spaced and the optimally-spaced resonator systems with identical resonators to shift away from the resonant frequency of the resonators so that all the power paths in the system can be utilized optimally to achieve the maximum efficiency. The cross-coupling effects of the non-adjacent resonators increase with increasing number of resonators and decreasing distances of the resonators.
Apart from the straight domino-resonator system which normally contains only one main power flow path, the domino-resonator system with two main power flow paths is also studied. One typical example of such systems is the circular domino-resonator system. Based on superposition theorem, individual power flow path of a circular domino-system is analyzed and then their interactions are merged and explained with vector diagrams. It is demonstrated that the optimum operating frequency could be far away from the resonant frequency of the resonators. However, if the operating frequency is fixed, the individual resonant frequency of each resonator in the system should be adjusted, for example by varying the compensating capacitances of the resonators, in order to regulate the power flows of the circular domino-resonator system to an optimum distribution.
As the simplest and typical multi-receiver domino-system, a system consisting of one transmitter and two receivers is studied. Theoretical analysis and numerical simulations show that the coupling between two receivers could be either helpful or harmful or even irrelevant to the power transfer efficiency of a system. All possibilities have been tabulated and explained. When the effect of the output power ratio is considered, three methods to obtain a desired output power ratio are introduced. It is proven from the simulation and experimental results that the efficiency can be improved significantly by optimizing the compensating capacitances in some cases, while in other cases operating at the resonant frequency of the resonators is already good enough. This phenomenon is favorably explained with the help of the power path concept. In addition, it has been found that a strong coupling between the receivers can help achieve a higher efficiency within a large variation of the output power ratio.
Notes: CityU Call Number: TK7895.P68 Z45 2012; vii, 159 leaves : ill. 30 cm.; Thesis (Ph.D.)--City University of Hong Kong, 2012.; Includes bibliographical references (leaves 153-159)Sun, 01 Jan 2012 00:00:00 GMThttp://dspace.cityu.edu.hk:80/handle/2031/69602012-01-01T00:00:00ZSystem identification algorithms and techniques for systems biology
http://dspace.cityu.edu.hk:80/handle/2031/6959
Title: System identification algorithms and techniques for systems biology
Authors: Zhan, Choujun (詹儔軍)
Abstract: Mathematical models for revealing the dynamics and interaction properties of biological systems play an important role in computational systems biology. This PhD work
is motivated by the current difficulty in system identification of dynamic biochemical pathways, given limited highly noisy and spare time-course experimental data.
In this thesis, the inverse problem of identifying unknown parameters of dynamical
biological systems, which are modelled by ordinary differential equations (ODEs) or
delay-differential equations (DDEs), is treated using experimental data. In some cases,
even the model can sufficiently describe the measured data, it is still important to
infer how well the model parameters are determined by the amount and quality of the
available experimental data, which is essential for investigation of model prediction.
For this reason, another key topic in this thesis is identifiability analysis.
The main contributions of this PhD work are summarized as follows:
1. In many cases, bio-system models are autonomous systems, which are linear in
parameters. For this type of models, an optimization-based parameter estimation approach is proposed. Spline and numerical differentiation methods are
used to smooth noisy observations and to estimate the time derivative of the
underlying dynamical system, respectively. Subsequently, the parameter estimation problem can be reduced to a Least-Squares Parameter Estimation (LSPE)
or a Linear Programming Parameter Estimation (LPPE) problem, which can then be efficiently solved by many global optimization algorithms.
2. For general bio-system models, a parameter estimation method combining spline
theory with Nonlinear Programming (NLP) is developed. This method removes the need for ODE solvers during the identification process. Our analysis
shows that the augmented cost function surface used in the proposed method
is smoother; which can ease the optimal searching process and hence enhance
the robustness and speed of the search algorithm. Moreover, the core of our
algorithms is NLP based, which is flexible and where consequently additional
constraints can be embedded/removed easily.
3. In practice, time-delay feedback pathways exist in many biological systems,
which can be modelled by continuous delay-differential equations (DDEs). In
this work, a two-stage approach is adopted for parameter estimation: first, by
combining spline theory and NLP, the parameter estimation problem is formulated as an optimization problem with only algebraic constraints; then, a new
differential evolution (DE) algorithm is proposed to find a feasible solution. The
approach is designed to handle problems of realistic sizes with noisy observation
data.
4. Identifiability analysis of the so-called S-system is given. The basic theory is
developed and the structural identifiability of the S-system is proved. This work
also analyzes the limitation of existing structural identification approaches, revealing that these approaches face the risk of the overfitting/underfitting problem.
Notes: CityU Call Number: QH324.2 .Z45 2012; xiv, 4, 160 leaves : ill. 30 cm.; Thesis (Ph.D.)--City University of Hong Kong, 2012.; Includes bibliographical references (leaves 149-160)Sun, 01 Jan 2012 00:00:00 GMThttp://dspace.cityu.edu.hk:80/handle/2031/69592012-01-01T00:00:00Z